Games

R9M Lite module is a 900MHz frequency system which is specially designed for FrSky Taranis X-Lite transmitter. This being the "Lite" version of the R9 series works perfectly with all receivers in the R9 series. In addition, it gets super low latency and high precision thanks to the upgraded digital interface and high-speed data transmission. The long range receiver R9M Lite has the extreme performance with the ability to achieve long distances with one RF power output at 100mW.  SPECIFICATION Dimension: 62.4mm × 30mm×14.5mm (L×W×H) Weight: 20g Number of channels: 16 channels Operating Current: 100mA@7.2V RF Operating Frequency: 900MHz/868MHz RF Power (Non-EU): 100mW (with telemetry)  RF Power (EU): 25mW (with telemetry) /100mW (without telemetry) RF Power (Flex):100mW (with telemetry) Compatibility: R9 series receivers FEATURE Firmware upgradable on Taranis X-Lite Telemetry data transmission supported Long Range, Low Latency and High ... Continue reading →

FrSky X8R receiver Description The X8R is in a Smaller package then previous 8 channel receivers, but has so much more capability. The new SmartPort supports the new hub-less sensors as well as the older hub analog sensors.The X8R supports 8 standard servo outputs, and you can access all 16 channels by using the Sbus line with Sbus supported servos or use a FrSky S.BUS Decoder for the full 16 channels. Or you can use 2 X8R receivers in combination and the channels will sync 1-8 on the first and 9-16 on the second.The X8 protocol is also backward compatible! In D8 mode it work with the DHT, DJT, DFT and DHT-U transmitter modules. Features: More number of channels: 1~8ch from conventional channel outputs, 1~16ch from SBUS port,or combine two X8R to become a 16 channels receiver. Parallel two X8R to become a 16 channel receiver. With RSSI PWM output (0~3.3V) SmartPort enabled, realizing two-way full duplex transmission. Specifications: Number of Channels: 16 Dimension: 46.5mm x 27mm x 14. ... Continue reading →

FrSky Long Range Receiver Super 8 Antenna Description: Brand: FrSky Item Name: FrSky Super 8 Antenna FrSky Long Range Receiver Super 8 Antenna Specification Frequency Range: 868MHz ( EU LBT ) and 915MHz ( Non-EU FCC ) Peak Gain: 3dBi@900Mhz Feed Impedance: 50 ohm RF Cable: RG405 Semi-flexible Connector: SMA internal screw hole Compatible with modules: R9M and R9M Lite   FrSky Long Range Receiver Super 8 Antenna Features High efficiency Quick integration   Package Included 1 x FrSky Super 8 Antenna The latest FrSky Long Range so lets you strike gold with a quality FrSky Long Range gears, cruise on an FPV drone and fly miles with FrSky Long Range System. You can increase your hunting odds with a long range receiver, module, and other Long Range kits. HorusRC has all the FrSky Long Range gear as well as FPV Drone Other Kit. This makes us your one-stop shop for FrSky Gears. You can also find many other RC Gear that will beautify your FPV Drone Racing. A Great way to show off ... Continue reading →

The FrSky Transmitter X7 ACCESS features 24 channels with a faster baud rate and lower latency thanks to its high-speed module digital interface. As with the rest of the ACCESS transmitters, it provides a secure and reliable link, along with wireless firmware updating making it fully compatible with our newest line of OTA receivers. The battery compartment now uses 2 18650 Li-Ion batteries and can be balance charged via the Mini USB interface. FrSky Transmitter X7 ACCESS FEATURES Ergonomic and compact design Open source operating system Installed with ACCESS protocol High-speed module digital interface Supports spectrum analyzer function Supports wired training function Haptic vibration alerts and voice speech outputs Easily accessible battery compartment (*Batteries not included, adaptive with replaceable 18650 Li-ion batteries) FrSky Transmitter X7 ACCESS SPECIFICATIONS Dimension: 202.2mm*189.4mm*96mm Weight: 613g (without battery) Number of channels: 16 (ACCST D16) / 24 (ACCESS) ... Continue reading →

FrSky receiver V8R7-II will operate as normal with your Telemetry module without having to switch over to none telemetry mode. Also compatible with the none telemetry modules - as well as with both the TARANIS TX and the XJT module too. FrSky receiver V8R7-II Features: Advanced Continuous Channel Shifting Technology ( ACCST SYSTEM), robust frequency agility. Easy to bind and very fast link-up. Excellent reboot times. All channels are very effective and easy to set failsafe. Responsive and rock-solid in performance. FrSky receiver V8R7-II Specifications: Number of Channels: 8 Dimension: 33.5mm x 22mm x 12mm  Weight: 5.2g  Operating VoltageRange:3.0V-16.0V Operating Current: 30mA@5V  Compatibility: All 16 channels require the FrSky Taranis,or the XJT module. For 8 channels in D8 Mode you can use the FrSky Taranis or XJT, DJT, DFT, DHT and DHT-U modules What's in the Box: 1 x V8R7-II 2 x Short tool 1 x Manual Continue reading →

The following guidelines can help you to download and install the HP Envy 5055 printer: Firstly, you must open a new web browser and reach 123.hp.com/setup 5055. In 123.hp.com/setup 5055, you must click the link over there to download the driver. After that, this will direct you to the Drivers and Downloads section. On the next page, you will be selecting your operating system from the available list. Next, navigate to your system settings and check for the version of your operating system. Moreover, now, pick the correct version of the operating system. Check for the driver information and accept any agreement if available. Further, click the Download button to start with the downloading process. Finally, you must choose a location to save your HP Envy 5055 driver file. Now, access the driver file location and double click the driver file. This will start with the installation process of the HP Envy 5055 driver on your operating system. Move on with the on-screen ... Continue reading →

When trying to perfect their performance, RC hobbyists, pros, and even amateurs will frequently rely on RC Airplane Telemetry devices and systems, since a capable pilot should learn to better use his/her physical abilities and available technology, searching for ways to not only develop their own skills with practice but also to get as many as possible useful information about their vehicle’s behavior while flying. With that in mind, one telemetry essential yet basic product that is highly recommended is the FrSky Smart Port RPM and Temperature Sensor. Like many other sensors from FrSky, this one also works with the Smart Port interface and, when installed properly in association with an S.Port enabled receiver, it can send the acquired data to its respective transmitter ‘s digital Telemetry Radio System. Get yours now for just $18.20 at horusrc.com and improve the safety and performance of your flights! FrSky Smart Port System So… what is Smart Port? For those of ... Continue reading →

The FrSky X9D was undoubtedly the most popular FrSky radio for years. Even with competition from other veterans brands such as Futaba, Spektrum, etc., FrSky managed to get a large following with their line of Taranis products and in the forefront is the FrSky X9D. Naturally, after years of success, Frsky released an upgraded version of the ever-popular X9D with the X9D Plus variant and have subsequently phased out the original X9D transmitter from its product line. FrSky X9D Plus Initial Impressions The unboxing experience is pretty good. The X9D Plus comes in a carry case that is included with all purchase of the transmitter. The transmitter comes with the following accessories: Taranis X9D Plus (SE version) Charger Lanyard (Neck strap) Battery (pre-installed) Carry Case 1GB SD Card (pre-installed) That is plenty of stuff to get you started and my favourite is the carry case as it is quite tiresome and dangerous to carry your transmitter without any protection and this hard carry ... Continue reading →

One of the finest WiFi Extender in the market is AC1200 Mesh WiFi Extender. This device is built to avoid interruptions in internet usage and increase the coverage area of your existing wifi network noticeably this device is used. This device is attached to the router to attain a boosted connectivity with a broader coverage area. It supports dual band connection and increases the Wifi speed up to 1200 Mbps. It also supports new 802.11ac.11ac &b/g/n WiFidevices. It can be easily installed via WPS or via mywifiext.net. Connect AC1200 with WPS Connect the extender to a power supply, and place it in the same room where the router is placed. After plugging the Extender, wait for the Power LED to light green. If the Power LED does not light, press the Power On/off button on the side of the extender. Now press the WPS button placed on the extender, the WPS LED will blink. After two minutes, press the WPS button on your router. As the extender connects to your existing WiFi network, you ... Continue reading →

The Most powerful device which increases the range of your wifi network and provides you boosted connectivity is our Netgear Extender . We connect the mywifiext Extender to our computer through a router by two means Firstly by WPS and next is via web address www.mywifiext.net. We just have to press the WPS button on the router and the extender one by one within a time between no less than 2 min. And wait for the led light turning green and we are connected. To Setup a New Netgear Extender Using an Ethernet cable connect your range extender to your computer. Launch any web browser in your computer and type htpp://mywiext.net. Press enter key and search for the login page. Enter your default username and password ie: username-admin and password-password. Go to login and press enter. Select the setup key and go to the Wireless setting option. Now once you are all set to setup you have to go through a verification process and check whether the network key password i s the same that of ... Continue reading →